Kategori
433MHz Modül
Marka
DreamLNK
Stok Kodu
DL-RX06C-LO6
DL-RX06C-LO6, 433Mhz 6-Channel Switching Value Wireless Receive Module

DL-RX06C-LO6, 433Mhz 6-Channel Switching Value Wireless Receive Module

Teklif İsteyiniz

Lütfen aşağıda belirtilen detayları belirterek, fiyat teklifi talebinde bulununuz.

* ile işaretli olanlar zorunlu doldurulmalıdır. 

*
*
*
*
DL-RX06C-LO6 is a low cost, compact size, high sensitivity super heterodyne ISM band wireless receive module, with decoding (learning code) function. It adopts cost-effective wireless data receiving chip and low power consumption MCU

  • DL-RX06C-L06
  • 433/315 MHz
  • Receiving Chip with Decoding
  • 3~5.5V

  • -112dBm
  • 300m
  • 29*12.8*6mm
ÜRÜN BİLGİSİ

6-Channel Switching Value RF Receive Module with Decoding (learning code) Function


DL-RX06C-LO6 is a low cost, compact size, high sensitivity super heterodyne ISM band wireless receive module, with decoding (learning code) function. It adopts cost-effective wireless data receiving chip and low power consumption MCU, with built-in image suppression function, can support 3V-5.5V wide voltage power supply, which performs high receiving sensitivity, as well as good anti-interference performance.

This Switching Control Module can meet your needs (realize the application) by setting the logic state of N1 and N2, and independently leads out 2 ports as following: Pairing status LED indicator, SW learning code-checking button. The LED indicator and SW learning code-checking button can be led to the circuit board or casing of the product, which is convenient for the user to operate. 

DL-RX06C-LO6 leads out the N1 and N2 setting ends from the module, and the pins adopt a 2.0mm pitch to reduce the size of the module. It also adopts T-type board double-sided in-line pad design. Its bottom plate uses a slotted in-line method, which the module can be inserted directly on the circuit board and then wave soldering. By this way, it can save the soldering of the pin header and reduce the height of the module to 10mm.

DL-RX06C-LO6 are compatible with PT2262 and 1527 encoding. The corresponding decoding and receiving module can also be ODM (customized) according to different remote-control encoding types.


Features

● Frequency range: 315MHz, 433.92MHz (special frequency can be customized)

● Sensitivity: Up to -112 dBm

● Power supply voltage input range: 3V-5.5V (recommended working voltage is 5.0V)

● Latch and non-latching mode selection: Set N1/ N2 decoding, output latch / unlatching

● It can be used to learn PT2260, 2262, 1527 remote controllers with good rate compatibility

● Encoded data transmission rate 2.5K bps (Manchester encoding)

● OOK modulation mode, can work with PT4450, 115H, 113, R25 (2SK3356) and other transmitting

circuits

● Module size 29 × 12.8 × 6mm (T type plate)


Technical Parameter

Parameter Symbol  State

Reference Value

Min.  Typ.  Max.

 Unit
Working frequency Fc
315，433.92 ，— MHz
Modulation Mode

ASK
Receiving sensitivity 
50 ohm antenna direct input /1k Kbps -112  dBm
RF Receive bandwidth 

300  KHz

Data demodulation   bandwidth

Demodulation pulse width is 0.2-1ms

 1，2.5，— K

Low Power Average

Current

 I
v uA
Supply Voltage  VDD
3.0，5.0，5.5 V
Working Current IRC VDD=3.3V/315M 4.5 mA


VDD=3.3V/433M  6  mA

Logic Truth Table T1  T2  State description
M Flash mode

Low level(grounding)0

High level (floating)1

D1-D6 output Flash Memory, non-low power consumption, with ordinary TX

L Self-locking mode

High level (floating)1

High level (floating)1

D1-D6 output Latch mode, non-low power consumption, with ordinary TX

H Interlocking mode

High level (floating)1

Low level(grounding)0

D1-D6 output Latch mode, low power consumption, with delay TX
Reserved mode

Low level(grounding)0

Low level(grounding)0

 D1-D6 output Flash Memory, low power consumption, with delay TX
Note: To confirm that the setting is valid, the red DK tool board needs to be powered on and reset,every time after setting the N1 and N2 states

 

YORUMLAR
Bu ürüne ilk yorumu siz yapın!
Yorum Yaz
TAKSİT SEÇENEKLERİ
PIN DEFINITION
Pin Description
VDD

Power supply 3.0-5.5V, it is recommended to use LDO or battery output,

Standard voltage 3.3V or 5.0V
GND  Module grounding，Reliably grounded and close to the system filter capacitor
LED

External code-matching LED indicator, press 2S for code-matching, light on and flashes 3 times

quickly means matching succeed, 8S long press until light off to clear the code
VT Common signal terminal, high level output (signal status indication) when valid signal detected
N1、N2

Working mode setting pins, detailed setting refers to the Logic Truth Table. N1 set the signaloutput mode, N2 set the low power consumption and common receiving mode
D1-D6

D1-D4 for standard four-key remote control, and D1-D6 for standard six-key remote control respectively
ANT Antenna (Refer to Figure 3 to design the patch cord and signal feed point)

Description: D1-D6 data output, corresponding to different remote-control key values, can output0000-1111 BCD code (need to customize).


TAVSİYE EDİLEN ÜRÜNLER

MRTK-Q433-L20D , 433MHz RF Anten , SMA / Erkek, 90-180°,3dBi
MRTK-Q433-L20D , 433MHz RF Anten , SMA / Erkek, 90-180°,3dBi
195,94 TL
IPEX to SMA Dönüştürücü Kablo ; IPEX/f - SMA/f , 1.13 kablo
IPEX to SMA Dönüştürücü Kablo ; IPEX/f - SMA/f , 1.13 kablo
111,37 TL
IPEX , U.FL PCB Konnektör
IPEX , U.FL PCB Konnektör
37,12 TL
DL-RX06C-LO6, 433Mhz 6-Channel Switching Value Wireless Receive Module DreamLNK Türkiye Resmi Distribütörü DL-RX06C-LO6
DL-RX06C-LO6, 433Mhz 6-Channel Switching Value Wireless Receive Module

Tavsiye Et

*
*
*
IdeaSoft® | Akıllı E-Ticaret paketleri ile hazırlanmıştır.